Custom Wrought Iron Gates in Fern Creek, KY | New Gates Fitted to Your Existing Fencing
Do you need a gate installed at your home or business in Fern Creek? Louisville Custom Iron Gates Company builds and installs custom wrought iron gates in Fern Creek. We offer all our building and installation services in the area. And our crews are available for any kind of repair job too. Fern Creek grew out of farmland, so ranch houses on wide lots are popular in the area. Most jobs here involve installing a new gate into fencing that already exists, which means matching heights and rhythms that were never designed for an iron panel.
Call our team today so we can help you plan your project. In our first visit, we can look at the existing entrance and discuss which shapes, decorative details, and finishes would suit the space. We’ll explain the work included in the proposal and how we back the completed project.
Get a Free Quote in Fern Creek
Tying New Gates Into Older Fern Creek Fence Lines
A new gate hung next to an old fence is an engineering mismatch unless the hinge post is treated separately. Fence posts are sized to carry fence; a gate leaf is a cantilever. We set a 4"×4" steel hinge post at 3/16" wall on its own footing and leave the existing fence post doing the job it was built for.
- New gates tied into existing farm and chain-link fence
- Double-leaf swings that halve the load on each hinge
- Secondary openings sized for boats, trailers and mowers
- Hinge posts set independently of existing fence posts
- Conduit run during installation for later automation
- 11-gauge frames with 16-gauge picket infill
Fern Creek Gate Projects
- Fence-line gates: matched to the height of an existing run, with the hinge post set on its own footing.
- Double-swing driveway gates: two shorter leaves rather than one long one, which reduces hinge load and arc.
- Equipment and trailer openings: sized against the real turning approach, including mirrors and tongue length.
- Automation-ready installs: conduit and a crossover sleeve laid now so the drive is not cut later.
- Transition details: the join between a new iron gate and older fencing planned rather than improvised.
Which of these fits depends on what is already on the boundary. See the full range of gate services we offer.
Wider Frontages and Secondary Openings
Where a lot still carries an older perimeter fence, the gate has to tie into whatever is there. Post spacing and rail heights on older farm or chain-link fencing rarely match a new iron panel, so the transition detail needs to be planned rather than improvised at installation.
Wider frontages give room for a double swing gate, which keeps each leaf lighter and shortens the arc compared with a single leaf spanning the same opening. That matters for hinge wear and for operator sizing if the gate is going to be automated later.
A number of Fern Creek properties have a secondary opening for a shed, boat or trailer. Sizing that gate for the actual equipment, including mirrors and tongue length, prevents the common outcome of a gate that technically fits but cannot be used at an angle.
Retrofitting Automation to an Existing Gate
An existing manual gate should move freely, stay aligned and have suitable structural support before an operator is added. Automation should not be used to compensate for dragging hinges, a leaning post or a distorted frame.
Fern Creek Gate Questions
Can a new iron gate hang off my existing fence posts?
Almost never. Fence posts are sized to carry fence, not the cantilevered load of a gate leaf. The hinge post gets its own footing, set independently, even if it sits right beside the old one.
Can you match an old farm fence height?
Yes. The gate is built to the existing height so the line stays level, while being fabricated to a heavier specification than the fence it sits in.
Is a double gate better than a single across a wide drive?
Usually. Two shorter leaves weigh less individually, need less arc each, and put far less strain on the hinges than one long leaf spanning the same opening.
I might automate later. What should I do now?
Lay conduit while the ground is already open, including a crossover sleeve under the drive if you have two leaves. Retrofitting it later means cutting the driveway.
Get a Fern Creek Quote
We will look at what is already on your boundary and price from there.